Topic profile page for stay put adhesive.
This page has aggregated data from forum posts, threads, listings, online discussions, newsgroups, messageboards, and other online sources which contain user generated content for the term: stay put adhesive.
Started 1 day, 5 hours ago (2008-11-18 01:48:55)
by outbackdave
Dear Doctor and others, I just bought a used Sony CDP-C505 and it had the same problem as described by others. Besides the "chucking arm" thing though, I found a broken spring mount which is located by removing the bottom panel. The spring gives extra force upward to the laser/disk motor assembly. The spring attaches to plastic at both ends and the plastic had failed. I repaired it with a small...
Started 1 day, 12 hours ago (2008-11-17 18:43:00)
by HammerDown
Quote: Originally Posted by dirkdigles Thread necromancy, I know ... Curious though guys - I just bought the BX50 for my v9m, hoping to do the same operation (remove battery label, put ultra-thin scotch packing tape on, and put the original battery door back on, with new extended battery in place. No go. My battery just won't fit...
Started 1 day, 21 hours ago (2008-11-17 10:07:00)
by TemeculaTim
Has anyone used a non OEM gasket and had success? I spent a few frustrating hours over the weekend trying to put a new WS in. The gasket was a cut to fit type with the center locking locking strip. We got the gasket from the glass shop when we got new glass. We tried getting the gasket to fit on the glass and had problems with the corners rolling off. We also tried putting the gasket in ...
Started 2 days, 14 hours ago (2008-11-16 17:11:00)
by rlsiv
I'm going on my 3rd season with a dozen of them. I REALLY like the drakes, but the hens look like cartoons. Motion is good. My keels do not stay in place well at all - they were all slipping out constantly until I put some screws and adhesive in the slots behind the keels to hold them in. Paint/flocking has not held up nearly as well as I would have liked. Not even as well ...
Started 2 days, 21 hours ago (2008-11-16 10:08:00)
by havanagranite
Quote: Originally Posted by lthomps222 I am in the process of re-doing my hallway that leads into my basement. As soon as I am done typing this post I am going to finish sanding the new sheetrocked walls and prime. If you look in the picture, I have cinder blocks below the new sheetrock. I do not like the appearance of the cinder ...
Started 5 days, 6 hours ago (2008-11-14 00:58:00)
by Curtis N
Quote: Originally Posted by azpix how are you attaching the swatches to the flash? For the gels I use "out in the field", I use velcro on the ends. Just adhesive-backed velcro tape about 3/4" wide. I stick it to about 1/4" of each end of the gel and cover the rest of the adhesive with tape. There's a picture in...
Started 5 days, 15 hours ago (2008-11-13 16:27:00)
by kartracer23
I think the adhesive I used says 24 hrs. before applying polish. Not sure about parking on it. One note: Before you start putting down polish, make sure it's absolutely perfectly clean. I wet mopped it real good about 3 times and still didn't get it clean (should have hit it with a microfiber mop too). Anything on there will seal down to the tile in your first application - dust, dirt, etc. I ...
Started 5 days, 19 hours ago (2008-11-13 12:00:00)
by chrisall
I tried to fit one of those once & found that I just couldn't make it stay stuck down. In the end I did away with the little plastic things & put a few blobs of 'No Nails' or whatever 'Sticks Like Sh*t' type adhesive I had to hand in the groove & the problem was solved. Cheers, Chrisall.
Started 6 days, 9 hours ago (2008-11-12 22:12:00)
by minowevie
Quote: Originally Posted by Arcy Thanks all! (Double thanks to Rhys for bringing this back to the top while I was watching. With the flood of posts we've been getting this must have fallen to page 2 (or 3!) and I missed it). Lots of good ideas to try out and see what works best for me. I'm using 3M Scotch tape that says it's intended for wood (though it probably ...
Started 1 week, 1 day ago (2008-11-10 13:16:00)
by BeeRye86
I just got my first lipo battery. I have a slotted chassis touring car and after a lot of filing and dremeling the battery fits. Now I'm trying to balance the chassis. My idea is to stick lead weights on the bottom of the battery so they fit in the slots of the chassis and keep the CG as low as possible. The only problem is with the self-adhesive tape on them they are thicker than the chassis...
Started 1 week, 1 day ago (2008-11-10 13:16:00)
by BeeRye86
I just got my first lipo battery. I have a slotted chassis touring car and after a lot of filing and dremeling the battery fits. Now I'm trying to balance the chassis. My idea is to stick lead weights on the bottom of the battery so they fit in the slots of the chassis and keep the CG as low as possible. The only problem is with the self-adhesive tape on them they are thicker than the chassis...
Started 1 week, 1 day ago (2008-11-10 09:37:00)
by MotorWorX
Quote: Originally Posted by 04BlkVibe Sometimes..i see cars that had their rustproof done and it would seep through the door edges, or between door and fenders, etc..and make the car looks dirty. Will your product do that? Thanks. Hi there, No, our product will not start seeping out through the ...
