Topic profile page for roller lifters.
This page has aggregated data from forum posts, threads, listings, online discussions, newsgroups, messageboards, and other online sources which contain user generated content for the term: roller lifters.
Topic "Roller lifters" was discussed 0 times on 0 sites in last 3 months
Started 6 days, 7 hours ago (2009-12-21 12:20:00)
by justhereforinfo
Anyone running these lifters? I installed 1 as a replacement and I have a ticking noise which doesnt seem to be rocker related. Using a long screwdriver up to my ear, it sounds like its coming from the lower intake, not the valve cover. I've checked all the rockers preload several times. I measured the lifter every which way possible and its exactly the same. Are these lifters known to ...
Started 6 days, 18 hours ago (2009-12-21 01:01:00)
by AnTra
I have tried to get a correct answer on this and have given up the regular way (Internet search), It´s like 50% seems to think it´s working just perfect and the rest agree that´s not recommended?. Have also read that one some grinds of Hydraulic rollers it will work fine and on others grinds not?. Have also read that it should be OK as long as you set lash tighter?. Reasong...
Started 1 week ago (2009-12-20 16:05:00)
by cshuman
LS Hydraulic Roller Lifters I bought these as a replacement for my L98. They look identical to the stock lifters except the front and rear area above the roller is not slanted up like the stock ones. I could see were maybe with an aggressive cam the lobe may encounter the body of the lifter as it is moving across the roller. Has anyone had any problem with ...
Started 1 week, 2 days ago (2009-12-18 13:48:00)
by blown71
FS: SBC Comp Cams 8953-16 Hydraulic Roller Lifters +.300 Taller Hydraulic Roller Lifters has 2,000 Miles on It...Ran Great...Sounded Great... Had them in My Small Block Chevy 400 Dart Block with 6-71 Blower..No Nitrous Check out My Other Listing for Matching Valve Springs..Pushrods...Camshaft Specs From Summit Racing Website: Small Block Chevy 265-400 +.300" Taller for After ...
Started 2 weeks, 3 days ago (2009-12-10 01:53:00)
by C-Bo
A friend of mine has a brand new set of '96-'98 vortec hyd roller lifters, can they be used in the gen 1 sbc? 2nd question.. Can they be used with any hyd roller camshaft?
Started 2 weeks, 5 days ago (2009-12-08 13:32:00)
by Mus408
Talked to their tech. about them for use on street/strip setups. He said to run them at 0 to .005 lash hot,and there should be no problems with beating any valve train parts up. I guess the limited .012 travel soaks up some of the lash,like a solid roller lash ramp? Basically like running a low spring pressure solid roller cam? Right now I think I have an issue with a collapsing lifter,as one...
Started 3 days, 8 hours ago (2009-12-24 11:21:00)
by xstfudonniex
In something with only a 6700 RPM redline, I dont know if the power gains would be worth it to switch to a dedicated SR setup? If all i need is lifters to give this a shot, i think its worth a try. _________________
Started 5 days, 6 hours ago (2009-12-22 12:59:00)
by justhereforinfo
Quote: Originally Posted by tmoss that's a stock replacement lifter......... The part number is the same, but the one I purchased has 2 rings around the center. The center is bare in this photo. I'm done guessing, just gonna get a stock replacement set. I converted 2 to solid a while back and...
Started 4 days, 2 hours ago (2009-12-23 17:32:00)
by jyro
I've been looking at these, I am sure they are CAT made. linkbars lifters for $200 http://cgi.ebay.com/ebaymotors/ws/eB...K%3AMEWAX%3 AIT I have a buddy with a spintron at his shop, I would sure test these for a couple of hours at 150lb seat to see if they will holdup to racing. They claim to have a warranty http://www.catpep.com/application%20...NTY%202008. pdf
