Topic profile page for Teflon.
This page has aggregated data from forum posts, threads, listings, online discussions, newsgroups, messageboards, and other online sources which contain user generated content for the term: Teflon.
Topic "Teflon" was discussed 21,066 times on 2,250 sites in last 3 months
Started 4 days, 9 hours ago (2009-11-06 17:35:00)
by Pikachu G0
hey i got a cp 48 45 that was leaking between the reg and bottle i took the reg off and was wondering if i should put teflon tape on the threads before i put the reg back on i wanted to use loctite on the threads but i dont have any so will the tape be a good substitute also is there an oring on the bottom of the regs in cp tanks? when i took it off the first time there was ...
Started 6 days, 16 hours ago (2009-11-04 10:06:00)
by brokenheart
OK, I was changing the infusion set for my son last night. We use the medtronic silhouette infusion set . After I took out the introducer needle , the teflon cannula was filled with bl**d. I took a picture of it as you see in the attached image. We had to remove the infusion set, discarded it and redid the whole thing. If somehow, in rare cases, bl**d fills the teflon cannula, we ...
Started 1 week ago (2009-11-03 07:05:00)
by jopena
Master cylinder leak fixed by simple Teflon tape. Hello, I got a leak from my Master cylinder for the last 2 years. The first 2 times that I have refilled the fuild I didn't have troubles up until last month. Since than I had to top up on every 3-5 days. My uncle told me that he can fix this leak by only changing the seal. We ...
Started 5 days, 13 hours ago (2009-11-05 13:40:00)
by nel peach
I picked up at the Montreal IDF Congress , while visiting the Exhibitors Hall , October 22 ,2009 2 brochures . These infusion sets work with ALL pumps , it states. I was given Canadian brochures, with a website www.Orbit90.ca . They are manufactured by : ICU Medical,Inc. , San Clemente, CA , USA, 1-800-824-7890 . US website www.Orbit90.com ?? I have been promised some samples .They will ...
Started 2 days, 22 hours ago (2009-11-08 04:07:00)
by M5 Roggan
I had my 06 with 21k miles (35k KM) on the clock in for paint treatment last week. Primarily this was to conserve the paint over winter where we have salt and sand on the roads to melt potential ice and give better traction when the temperature is below freezing. I have done a lot of polishing myself the last few years including winning a few car shows with my previous car (...
Started 3 days, 16 hours ago (2009-11-07 10:45:00)
by michaelwooten
Re-design in 06 turbo Ref: those in the know...help thread. When I picked up my truck yesterday the tech told me that when he got the part it had a coating on it similar to teflon. Maybe to help deflect moisture? He is a master diesel tech and he said he swaps turbos all of the time, but this is the first one he has seen like this. ...
Started 1 week ago (2009-11-03 05:48:00)
by ShifflerGraphics
I am a graphic designer. I have the software and the Epson Photo 1400. From spending a few hours on the site, I think I need the following for the production aspect: Paper (Jet Pro Stretch) Teflon Sheets Heat Press (11x15 clamshell but what brand? ) Shirts (preshrunk 100 or 50/50 cotton) Anything else? Will the transfers leave a film or do I cut the designs out myself?
Started 2 days, 13 hours ago (2009-11-08 13:26:00)
by TshirtGuru
What do you put over foil when heat pressing? Using a spare tshirt seems to work best because it leaves a shiny finish on the foil but it doesn't transfer all of the foil (leaves some specks) I think because the tshirt is a bit thick. I used a teflon sheet and works well and foil transferred well with no specks but the finish was a bit dull and textured (the teflon sheet has a crisscross ...
Started 1 week ago (2009-11-03 14:59:00)
by compicat
In this cable, UniCrystal 18 AWG Solid OCC Copper wire (Ohno Continuous Cast) with FEP Teflon insulation and swithcraft 3.5mm plug have been used. This is great detailed cable. The cable part is solid, so when you bend the lod, it ll protect its position till you bend it to other way. It is compatible with all ipods including all generation iphones and ipod touches. Thanks. I want ...
Started 1 week, 1 day ago (2009-11-02 16:51:00)
by softrockrenegade
k guys i said id post pics of mine unlike the invisible one that went for 940 on ebay!!! this knife feels great , prettiest g10 i have ever seen and the teflon washers are smooth as silk. fit and finish is top notch and this thing locks up just as tight as a sebenza. im diggin it soo far!!!!
