Topic profile page for Spindles.
This page has aggregated data from forum posts, threads, listings, online discussions, newsgroups, messageboards, and other online sources which contain user generated content for the term: Spindles.
Topic "Spindles" was discussed 24,501 times on 1,064 sites in last 3 months
Started 1 day, 8 hours ago (2009-11-25 12:27:00)
by JustSpeed7
I have a complete front cobra brake kit, with spindles looking to get $300 for everything this is perfect for you fox body people looking to do a 5 lug conversion.
Started 2 days, 6 hours ago (2009-11-24 14:16:00)
by syzygy
How much benefit does one get raising spindles 19mm? 30mm? Currently I am experiencing obvious bumpsteer and likely notable suspension travel issues, as well. Does 19mm provide enough of a benefit or is 30m that much better? I am seriously considering getting this done along with a suspension upgrade. The big issue I have is that I have a set of 15 inch wheels I don't really want to lose ...
Started 3 days, 6 hours ago (2009-11-23 15:06:00)
by moschika
is it possible to swap bb spindles in a cup and bearing bb? i'm thinking of swapping out the old cottered set-up on the peugeot i recently acquired. could i just swap out the cottered spindle for a square-tapered stronglight spindle? this way I don't have to deal with getting french threaded cups?
Started 3 days, 13 hours ago (2009-11-23 08:00:00)
by pupjoint
Looking to buy a set of ball joint dropped spindles for my other vehicle. i know CB's unit has been around for some time. Any idea on Airkewld's unit? they are both priced around the same. I cheked their site, they have veryice looking kits, with lifetime warranty on the rotor, but only looking for spindles now. Are they both forged? both have around the same ...
Started 3 days, 20 hours ago (2009-11-23 00:42:00)
by GCncsuHD
Saw this on craigslist, not too bad for a set of spindles, blocks, and shocks. Donkify your ride or lift your 2wd http://charlotte.craigslist.org/pts/1478004244.htm l
Started 3 days, 21 hours ago (2009-11-23 00:06:00)
by 03ChvySlvrdo
I have a 03 silverado 2wd. I plan on putting the 3" Sprintech spindles, 2" spacers, and 2" blocks on it. My question is if i put the Springtech spindles on there, will I have to use wheel spacers?
Started 3 days, 21 hours ago (2009-11-22 23:09:00)
by 03ChvySlvrdo
I have a 03 silverado 2wd. I plan on putting the 3" Sprintech spindles, 2" spacers, and 2" blocks on it. My question is if i put the Springtech spindles on there, will I have to use wheel spacers?
Started 3 days, 22 hours ago (2009-11-22 22:44:00)
by trashn'l
I have a new MAS 2" tube straight axle for Chev spindles. It has had the spring pads and shock mounts welded on and is painted silver. It measures 48" from kingpin center to kingpin center and 34.5" from spring pad center to spring pad center. Also included are a set '53 Chev. spindles with steering arms, the steering arm for steering draglink (see how to section on www.gassersinc.com)and a set...
Started 3 days, 23 hours ago (2009-11-22 21:45:00)
by PJ-4.2L
I need both rear SC half-shafts in good condition, attached to the rear spindles. I will be swapping on my Mustang hubs, so I don't need T-Bird hubs. I'm in the process of swapping from a rear drum setup so I need to be sure the spindles come off a car with rear disc brake setup. I also have an aluminum 8.8 rear end with Ford Motorsport 4.10s and an Eaton diff- professionally installed by ...
Started 4 days, 8 hours ago (2009-11-22 12:26:00)
by Anchorboy46
Ford 37-41 Ford spindles Wanted: Parts Location: Crockett,Texas Wanted Ford spindles 37-41 Dead or alive- PM Anchorboy46 or email Anchorboy46@yahoo.com.Thanks
Started 4 days, 6 hours ago (2009-11-22 14:54:00)
by S-351
Mint condition lightweight CPC chrome moly A-Arms and CPC Spindles powder coated black for Arctic Cat Thundercats. Just used for mock up, never used. CPC sells the A-Arms alone powder coated $465.00 and the Spindles for $525.00 willing to sell for $775 shipped to anywhere in the US. Bryant 952-451-7779 svt162@hotmail.com
Started 4 days, 6 hours ago (2009-11-22 14:54:00)
by S-351
Mint condition lightweight CPC chrome moly A-Arms and CPC Spindles powder coated black for Arctic Cat Thundercats. Just used for mock up, never used. CPC sells the A-Arms alone powder coated $465.00 and the Spindles for $525.00 willing to sell for $775 shipped to anywhere in the US. Bryant 952-451-7779 svt162@hotmail.com...
Started 1 week ago (2009-11-19 04:53:00)
by trip1019
Hello, I am new to the site. first post. I am going to do a 5 lug swap on my 1986 mustang. going with Cobra rotors up front. My question is, Will 2000 Mustang spindles work for this swap or do I have to use the 1994-95 spindles?
Started 1 week, 1 day ago (2009-11-18 19:07:00)
by LS Xtreme
Hey guys, Read some articles about people putting 2000'ish Camaro front pads and rotors on the 2WD blazer spindles? Anybody have any info on this? Just looking for an economical upgrade for the Blazer brakes. on my Xtreme, Thanks in advance for the info!
Started 1 week ago (2009-11-19 19:13:00)
by skratpiece
WTB: IRS Parts. 03/04. Need spindles, halfshafts, calipers. I'm piecing together an IRS for my friends fox body. I need spindles, halfshafts, and calipers. Shoot me a pm. Thanks.
Started 6 days, 18 hours ago (2009-11-20 02:10:00)
by supercharged z06
Anybody have any experience with driving a corvette with drop spindles on the track? What adjustments to the suspension would you have to make since the center of gravity,the roll center, and the roll stiffness are going to change?
Started 1 day, 3 hours ago (2009-11-25 17:53:00)
by MacogansStreetRods&Muscle
I am building a Pro Touring Chevy s10. I would like to know if anyone has any ideas on or if there is a spindle made that will accept c5 brakes or a big brake kit for a 96 s10 chassis
