Topic profile page for Rivets.
This page has aggregated data from forum posts, threads, listings, online discussions, newsgroups, messageboards, and other online sources which contain user generated content for the term: Rivets.
Topic "Rivets" was discussed 0 times on 0 sites in last 3 months
Started 3 days, 11 hours ago (2009-12-25 16:23:00)
by R.C.Reichert Registered User
I have a large Hudson Bay camp knife that I am making which I used brass washers and brass pins for rivets. I would like to be able to have the riveted heads stand "proud" as they say so they stand out from the washers. My question is how do I prevent or deal with the problem of the rivet heads developing sharp edges on it as it's formed? I will include a photo of the knife so you can see what ...
Started 4 days, 11 hours ago (2009-12-24 16:18:00)
by MRevoKIDD
hey guys, im installing my new jdm rear and im trying to take off the rivets off the oem bumper..is there an easier way or you pretty much have to just yank that shiit out?
Started 5 days, 16 hours ago (2009-12-23 12:09:00)
by aelliott
Folks: When building (or fixing) your plane, you'll probably need to remove and reset a bunch of rivets. For best structural integrity, you probably should re-do any rivet that seems even the least bit marginal. The best and safest way to remove a pulled rivet without damaging the surrounding material or the hole is to: Punch out the rivet mandrel. Carefully drill off the rivet ...
Started 6 days, 5 hours ago (2009-12-22 23:16:00)
by harryford
Hello, I am looking for flats, preferably tapco but I am open to anything, they are for bulgy ak74 and rommie ak, I also need rivets, I would also prefer to buy from around the Sacramento area. Let me know Thanks
Started 1 week ago (2009-12-21 10:06:00)
by techy330
hey can someone just verify that this is the right part i need a few new expanding rivets for the zhp side skirts. The ones that popped off when the jack slipped are about the size of a half dollar at the top. I found what looks to be the right part on pelican parts but I don't have a diagram in order to confirm the part number. Once again they are the expanding rivets on the bottom side of the...
Started 1 week, 1 day ago (2009-12-20 18:04:00)
by skyflies
I live in a townhouse with a one car garage. The garage adjoins the neighbor's garage. My condo association rules have something about "general nuisance" so it's a pretty broad category to catch things like riveting My question is, what % of rivets can you squeeze? I imagine you cannot do much when putting the skins on but I was curious anyway. I plan to do a test in the next few ...
Started 1 week, 2 days ago (2009-12-20 03:31:00)
by mcattell
I riveted the canopy to the canopy frame over a week ago. Tonight I discovered a bag of aluminum pop rivets that were intended for the canopy. Oops, I installed standard CS4 rivets. The CS4 rivets seemed to work fine. Is there any problem leaving those in? I'm guessing the alumuminum ones are softer but now that's it's done I hate to drill all of them out and risk damaging something. Plus ...
Started 1 week, 2 days ago (2009-12-19 15:51:00)
by driverm3bk
I am replacing the windshield on my R100S and I can't get the center pin on the plastic rivets to seat all the way down. They go about half way and stick. Any ideas? Thanks, Brad Kuhn
Started 16 hours, 39 minutes ago (2009-12-28 11:37:00)
by El Chupacabra
I have a set of G3 "alpinist" skins (little metal hook tips) that I'd like to use on Mrs. C.'s skis. Problem is, they're a little too long -- they're marked as being for "170-180 cm" skis, and I need them to fit 167cm K2 Chiefs. They already have the G3 STS-style tail kit attached to the tails. I know I can cut off the G3 tails and buy a Black Diamond STS kit to get the stretchy rubber ...
Started 13 hours, 4 minutes ago (2009-12-28 15:12:00)
by Quadzilla
I think you can get the stock rivets from Reno Mt. Sports. Just drill out the old ones and use a ball peen hammer to hammer the stock rivets flat. Make sure you hammer on a hard surface like the top of a vise or anvil.
Started 6 days, 5 hours ago (2009-12-22 22:27:00)
by Beamermon
I need to remove the passenger side window glass. It looks like there are 2 rivets that have to be drilled out to remove the glass??? Has anyone pulled the side glass out of a SN95 and can help me out ? Thanks
Started 4 days, 18 hours ago (2009-12-24 09:38:00)
by CRAZYBUBBA
Special Features: Hidden pocket rivets Crotch rivet Single stitched back pockets Two-tone lemon stitching Two-tone selvedge Coin pocket selvedge V stitched top button Raw indigo denim Button Fly Off-center back belt loop, etc. Condition: Mint condition, the pics don't do it justice. NO stains, NO rips, NO holes, NO tears, NO ...
Started 3 days, 8 hours ago (2009-12-25 20:12:22)
by brianrichardson
This car came in the display case pictured below. I've waited forever to own one and now I finally do. Red Ransburg McQueen is very difficult to photo. The car is actually more orange than red. So here are a few photos: no date code, non tampered rivets note the painted gas cap passenger side tampo is slightly crooked acutal case that came with this ...
Started 6 days, 16 hours ago (2009-12-22 11:24:00)
by drynoc
There is a piece of black plastic under the front of our cars, attached with plastic rivets to the front fascia. I recently scraped it off of the front of my 00 ES while driving in ice and snow, and I'm wondering if I need to replace it. What purpose does it serve other than warning me that I am scraping the curb when I park?
Started 1 week ago (2009-12-21 11:44:00)
by inZane 240
ZG Flares from MSA for sale. Never used. Fiberglass. One flare has very small pilot holes drilled for rivets/bolts. Pickup: $120 Shipped: $140 I am located in Lodi, CA and work in Concord, CA Also looking for a 81-83 5spd and s30 hatch so if u wanna trade let me know.
Started 5 days, 14 hours ago (2009-12-23 14:14:00)
by A6/2.7t/S-line
some quick pics of the Rs6 front grill mod: removing the lower support bar some people used a dremel but but I used a grinder (for ceramic) took less than 10 minutes to remove, just have to be cautious. i went straight for the rivets (no drilling them out) and sliced them with the grinder I can post better pics if anybody needs some
