Topic profile page for PRV.
This page has aggregated data from forum posts, threads, listings, online discussions, newsgroups, messageboards, and other online sources which contain user generated content for the term: PRV.
Topic "Prv" was discussed 3,021 times on 499 sites in last 3 months
Started 1 week, 2 days ago (2009-11-27 10:37:00)
by web_surfer
In past posts on this forum I believe the general consensus is that a PRV is not needed if water pressure is under 80psi. A couple of months ago the new copper plumbing was completed - all type L. 1" from meter to water heater & 3/4" after that to various locations that then divide off into 1/2" for individual fixtures. Used soldered on Nibco ball valves. Also, based on reading this forum...
One room w/ Prv Bathroom in a six-room nice house which is very close to USC campus, only one block away (at the crossing of Jefferson Blvd and Catalina Street), five minutes by walk, very safe area. $850 per month. WIFI, utilities included, cable, kitchenware and furniture provided, large backyard with free parking. Nice housemates (Three Chinese girl, an Idian guy and an American...
Started 3 weeks, 5 days ago (2009-11-10 12:09:00)
by prq123
We had a pilot PRV stick full open for about 12 hours. When the PRV was taken offline fore repairs it was noticed that the PRV soft seat had partially melted along the outside edge. The melting temperature of the soft seat is > 160 deg C, however, the measured gas temperature during the relief (and normal operating temperature) was only 100 deg C. The gas temperature has never exceed 110 ...
Started 1 month ago (2009-11-04 10:20:00)
by lam1303
Hi guys! We received a letter from the county that there is going to be a significant increase in water pressure and we should install a PRV. We already have a PRV along with a thermal expansion tank installed where the pipe comes into the house, but it was suggested we have one installed at the water meter. Is this necessary? There are several neighbors who have had pipes break ...
Started 1 month ago (2009-11-03 17:49:00)
by tom_in_seattle
I'm installing a small 2 gal electric supplemental water heater for the downstairs 1/2 bath. I want to do this so guests don't have to wait to receive hot water from our tankless unit located some distance away. I am planning to run the PRV discharge line down into the crawl space and would like to run it into what I've been told is a flood drain to the sewer... essentially a 4 inch flex line ...
Started 1 month, 1 week ago (2009-10-30 00:00:00)
by rogeriodec
Although I use Sonar for many years, there's one thing I remember that is easier in Cubase and do not know if Sonar already has. When working in PRV mode manipulating envelopes, for example Modwheel, and I leave it in half (64 value or any value), when I want to remember what value is after a long piece of music, gotta get back visually to the last envelope and put manually with the mouse in ...
Started 1 week, 1 day ago (2009-11-28 08:23:00)
by Xler8n
I have a 1995 325i with 203,000 miles on it. I failed emissions here in Maryland saying that my hydrocarbons were too high.. So too much unburnt fuel... I thought that maybe changing the spark plugs doing an oil change and cleaning my air filter would do the trick like a tune up.. While changing the plugs i found oil in the compartments so i'm sure i need to change the valve cover gaskets.. I ...
Started 2 days, 21 hours ago (2009-12-03 17:46:00)
by AgerTank
6 available - these are Pub Manufacturing single wall serving vessels that were used with a 7 bbl system. The markings on the tanks indicate 9bbl gross cap. They are fitted with dome top/dish bottom and side manway doors. Measurements are approx 42" diameter x 84" tall and include prv, sample port, sight tube, 1-1/2" tc bottom drain with butterfly valve, and cip. Tanks are in very good shape ...
Started 5 days, 10 hours ago (2009-12-01 05:06:52)
by native
I played around with Beatscape a bit and created some grooves. how do I use import these into my project? I tried drag and drop, but doesn't seem to work. also, can I edit a groove later on in PRV?
Started 4 days, 15 hours ago (2009-12-02 00:00:00)
by Ch Conceptz
02 Audi TT ALMS Ed - 225 Quattro - Few Mods 2002 Audi TT Quattro. "ALMS Ed" Avus Silver w/ Red Nappa Leather Interior. 18in Wheels 43,000 miles. 2nd Owner Originally a WI car. Prv Owner bought it after leasing it from new. Bone stock most of its life. Full loaded ( No nav ) Exterior and INterior all in excellent shape. All Mods done with in the last 5,000 miles....
Started 1 week, 1 day ago (2009-11-28 08:45:00)
by pravena
Hey guys, I’m taking part in a modeling competition and I need your support to get through to the next round. In order for that to happen I will need all of your support. So PLEASE VOTE FOR ME guys! Just type: MODV PRV and SMS to 36660 RM 1.00/vote. Telco charges applied Thanks guys. Love, Pravena XOXO p.s do check out MODELLE mag for my pictures and the competition, ...
Started 5 days, 6 hours ago (2009-12-01 09:09:00)
by Special A Gent
Hi Last time I posted I baled part out in the 70's Bought into VGM and am sitting on a nice profit, just waiting for December update, before considering selling part and re-considering PRV. What is the problem with PRV share price? Have you any news? Would like to increase holding, but seems a big risk judging by the sp fall? Now back to my average. Any suggestion welcome. S.A.G...
Started 2 days, 18 hours ago (2009-12-03 20:50:00)
by michb
Hi, we are changing an old rad valve for a new trv. We have a combi boiler. Do we need to drain the entire system to change the rad valve or can we just let the pressure out of the boiler from the prv? Many thanks
