Topic profile page for Oil pan.
This page has aggregated data from forum posts, threads, listings, online discussions, newsgroups, messageboards, and other online sources which contain user generated content for the term: Oil pan.
Topic "Oil pan" was discussed 44,777 times on 1,002 sites in last 3 months
Started 14 hours, 7 minutes ago (2009-11-28 01:47:00)
by cudawebber1
i need some of the following for a 1998 dodge dakota 5.9 oil pan and pickup pcm for the 5.9 and maby the wiring harness under the hood and also need headers all for the dakota im not in a big hurry for the parts just want to see whats out there.and also need a distributo for the 5.9 engine i would like to get some of the parts but im not in no rush to get every thing right now thanks.
Started 20 hours, 33 minutes ago (2009-11-27 19:21:00)
by peterv
I searched and couldn't find a diy for the oil pan gasket. I have the Bentley manual and it's pretty much straight forward. I was wondering if there is a way to support the engine from the bottom as opposed to from the top. I don't have the tool to lift the engine from the top. BTW, this is for a 2000 328i auto if it matters.
Started 23 hours, 4 minutes ago (2009-11-27 16:50:00)
by chefro
EDIT: C4, 12V, AFC engine I am thinking of replacing both, the upper and lower pan gaskets. Did anyone have to ever change their upper gasket? While the lower gasket is fairly easy to replace from below, of course(although the sway bar seems to be in the way of some of the pan's bolts), is the upper one done also from below, or you have to pull the engine out?...
Started 23 hours, 14 minutes ago (2009-11-27 16:40:00)
by strictlyvanagons
VW Vanagon diesel oil pan- never bolted to anything. Will bolt to 1.6Lt. and 1.6 Lt. TD diesel motors and to gas engines. Most likely will bolt to 1.9 TD and 1.9 TDI motors. Do your own research!!!! $100 CASH in person or with extra cost shipping postal monet order or check from Bank of America will work. NOTHING ELSE!!!!!! NO paypal!!!!! PHONE CALLS ONLY!!!!!413 563 1829 7am-11pm 7 days. ...
Started 1 day, 3 hours ago (2009-11-27 12:30:00)
by vtec-this
is the upper and lower oil pan interchangeable from the ge motor to the gte aristo motor? ive been lookin and cant find out and help would be greatly appreciated. and if any one is wondering why i totaled my gs and as far as i can see for now that seems to be the only thing wrong to the motor so i hope
Started 1 day, 11 hours ago (2009-11-27 04:30:00)
by kpodj61240
So I have been reading around and talking to people about oil cooling issues and most said that a bigger oil pan would be fine instead of running an oil cooler. So then I was on a search to find one. ISIS($119) vs Greddy($375.99) vs Moroso($299) vs ARC($399.99)....hmmm I wanted the Moroso cuz my car is pretty low and that specific pan is same as oem height and people complained weather Greddy or...
Started 4 days, 10 hours ago (2009-11-24 05:40:00)
by emil
Since they're all M30s, would an oil pan gasket meant for an E28 535i/E24 635CSi work on an E34 535i? The oil pan mating surfaces are the same as far as I know, so it should fit fine, correct? Cheers, -Emil
Started 6 days, 11 hours ago (2009-11-22 04:11:00)
by needmorepower
In-truck oil pan change I know some of you have done it, but I can't find those threads now. I'm thinking about doing this to my Lightning when I get to see her again this Christmas, since it's cracked and I don't have an engine hoist. Obviously, I have to remove the upper intake so I can jack the engine up, but do I have to unbolt the transmission, too? Take the driveshaft ...
Started 3 days, 15 hours ago (2009-11-25 00:35:00)
by thedave78
milodon oil pan Milodon oil pan, pickup tube, and high flow oil pump for a 351M. I think it will fit a 351C but i'm not positive. None of it has been used, I'm going a differet way with my project and do not need them. $100.00 plus shipping from mtn. home idaho e-mail is thedave80@msn.com dave...
Started 5 days, 22 hours ago (2009-11-22 17:42:00)
by DirtyDzl
Steel oil pan in place of Aluminum one? Didn't find much searching. Busted the aluminum one and have one from an 85 8v, i've heard sludge can be a problem with steel oil pans...but since TDIs call for Synthetic (which i use). I see no problem. Aluminum oil pans suck for lowered cars.
Started 2 days, 23 hours ago (2009-11-25 16:10:00)
by DB8TEGSTER
FS: B16 OIL PAN MINT CONDITION Price $40 Contact information Db8teggin@yahoo.com Is the item new or used Used -------------------------------------------------- --- Product description I got a mint condition b16 oil pan. $40 gets it. -------------------------------------------------- ----...
Started 1 week, 1 day ago (2009-11-20 14:27:00)
by ninetyfivevette
Does anyone know if the windage tray used with the Canton 7qt road race pan will work with the stock oil pan? I'm hoping to just swap oil pumps and return to the stock pan. I seem to recall the windage tray is held in place by some studs on the main caps. It's been a while, so my memory is foggy about that....
Started 2 days, 15 hours ago (2009-11-26 00:42:00)
by tyshonea Member
I have a perfect condition oil pan from a 1993 325i sedan. 95k miles on it, it is cleaned up and ready to go. Local pickup from San Diego would be nice. $80.00 plus shipping. [IMG]file:///c:/oil%20pan%201.jpg[/IMG]
Started 2 days, 19 hours ago (2009-11-25 20:45:00)
by peterbilt1214
well put my motor in and the oil pan is hitting the cross member so we are going to have to pull it and do something any suggestions on a new bell housing or something i can do to make this one work. thanks guys
Started 1 week ago (2009-11-20 22:05:00)
by odyvan98
FT Engine Motor Mount & Oil Pan Leak I took my Honda Ody 98 to have my timing belt replacement. They told me that I need to replace the FT Engine Motor Mount and Oil Pan needs to be sealed. Anyone has these repair works before? Thanks!
