Topic profile page for Ignition switch.
This page has aggregated data from forum posts, threads, listings, online discussions, newsgroups, messageboards, and other online sources which contain user generated content for the term: Ignition switch.
Topic "Ignition switch" was discussed 17,687 times on 866 sites in last 3 months
Started 2 days, 3 hours ago (2009-11-25 16:51:00)
by BradyTrailRats
Key won't turn in the switch tried 2 keys same results Jeep is parked on a bit of an incline i'm thinking either ths steering lock or maybe the shifter lock (automatic trans ) is jamed...can i easily disable one or both
Started 2 days, 4 hours ago (2009-11-25 15:30:00)
by JDC
Hey guys,I switched out the ignition switch on my 90 SC automatic,tried to turn the key switch(cylinder)it won't turn.I did take out the key switch and put it back in.What have I done?????Please help,and as always thanks.I really appreciate all of you for the help on the thread Starting 90SC,and still working on it.Thanks JDC
Started 2 days, 20 hours ago (2009-11-25 00:15:00)
by curley03
I changed the tank and went with the 5 gal. UE trick tank. I have the bracket to move the switch to the front cylinder. I went keyless with the Guard Dawg switchless ignition. The switch itself is not working so its not included. I have the 3 wires that are needed to connect the switch included. I'm selling the bracket and 3 wires for $25.00 to cover the cost of shipping. Pay Pal OK
Started 3 days, 1 hour ago (2009-11-24 19:12:00)
by tom shewchuk
Ignition switch cover from a Duetto. Very good condition. No marks scratches scuffs or cracks. Not even a scuff from dangling key rings. As good as they get. $70 plus postage.
Started 3 days, 7 hours ago (2009-11-24 12:49:00)
by bignick
I've been helping a guy get his 78 beetle running and I've encountered some confusing issues. The starter wasn't working so I got to checking it. Everything seemed normal except the signal wire from the ignition to the solenoid has a constant 12v. Key can be off and its getting 12v. He told me that it used to have trouble starting and it required turning and holding the key to 'start' ...
Started 3 days, 20 hours ago (2009-11-24 00:00:00)
by Roland Finston
how to disassemble the key switch to a 2002 chrysler concorde  Answer Hi Roxann, The switch is attached to the lock cylinder housing on the opposite end from the key insert. Disconnect the negative battery clamp (the switches mentioned below are 'hot' so you want to avoid shorting but this isn't absolutely necessary particularly so as to avoid other 'gremlins' from doing that; just be ...
Started 1 week ago (2009-11-20 01:37:00)
by geonapa
Ignition Switch wires problem... Forum friends, as soon as i parked the bike at my work and it was idling and before i switch it off, it switched off by itself. Wondering what is happening, i moved the wheel bar left and right and it switched on, off, on and so on. Doing a quick check, i found out that a wire coming out from ...
Started 1 week, 1 day ago (2009-11-19 04:45:00)
by fireeagle7806
Hello Everyone. I am rebuilding a 1989 Mustang that has been sitting for awhile, I can get it to start but the ignition tumbler rolls back to far from run position and car will not stay running unless you hold key forward. I have already replaced tumbler and key. This is my first major rebuild and I have ner seen this problem before......any advice would be appreciated...Thanks in advance
Started 1 week ago (2009-11-20 00:05:00)
by beto78
Hi fellows. i'm not american, so my english is not very good please try to understand if i write something wrong. I have a mexican '78 mach 1 mustang. i just replace a broken ignition cylinder and now i have a question, that anyone with a mustang II can answer. when you put in the key in the lock position. can you turn the switch back to turn the accesories on like in new cars? thanks
Started 1 week, 1 day ago (2009-11-19 00:50:00)
by _juice_
ok, i found a truck sitting in a guys yard for about 6 months and i finally decide to stop and ask him about selling it yesterday. right now it only has the cab and doors on the truck. It was in a wreck, so he took the bed and frontend off and uses it to play in the woods. anyways,he bought the truck with no title so we dunno what year it is and he lost the keys to it a few months ago. So...
Started 1 week, 1 day ago (2009-11-18 22:18:00)
by rensho
My 2005.5 avant doesn't hold power when I switch off the ignition. This means no radio as soon as I turn off the motor. Something doesn't seem right. My past Audi, 97 a4, would hold power until i removed the key. I noticed that when I insert the key, without trying to start the motor, the only position I seem to have is ON. This will activate things and turn on the lights/radio. Does ...
Started 1 week ago (2009-11-20 00:28:00)
by airhook
Disco 11 TD5 P/N QRF101050H OK, my wife broke the key off in the ignition switch. The car was immovable, steering lock on, immobiliser activated. About 1cm of the key is stuck in the lock. I've got the lock off the car & am managing to start it with the broken key taped to the reciever & a screwdriver. Has anyone got a suggestion on how to get the broken bit out? I've tried the local ...
Started 6 days, 20 hours ago (2009-11-20 23:46:00)
by iggysepia100
These are the latest two items I have on ebay from my 1988 Razz. They are in perfect shape. Let me know if you want them and I will end the listing provided that the item has not been bid on yet. Thanks. Iggy.
How do i replace ignition starter switch on 2005 ram 2005 5.9 cummins. Answer NOTE: The steering column on vehicles equipped with an automatic transmission is not equipped with an internal locking shaft with the ignition cylinder. Alternative methods of locking the steering wheel for service will have to be used. The tilt and standard column (4) (STEERING COLUMN) have been designed to be ...
Started 1 week, 1 day ago (2009-11-18 23:34:00)
by antonio fuller
Hey I got a 2001 ls the ignition switch want turn sometimes when I put the key in the key is ok it will open the door find what's up with this how do I fix it
Started 4 days, 1 hour ago (2009-11-23 18:41:00)
by wk2fish
I have a 1998 tacoma 4cyl auto. The other day I could not turn the key and remove it from the ignition switch. I removed the shifter cover and disconnected the wire going to a switch on the right side of the shifter and was able to remove the key. I have not removed the switch yet and was wondering if there is an adjustment or will I need to just replace the switch? And ...
