Topic profile page for Hydraulic.
This page has aggregated data from forum posts, threads, listings, online discussions, newsgroups, messageboards, and other online sources which contain user generated content for the term: Hydraulic.
Topic "Hydraulic" was discussed 0 times on 0 sites in last 3 months
Whoops! When you disassemble & reassemble a $3000... Whoops! When you disassemble & reassemble a $3000 hydraulic valve make sure the o-rings are seated properly or it's gonna leak. My bad. 2:17 PM Jun 23rd from txt
Started 14 hours, 18 minutes ago (2009-12-24 02:50:00)
by ls02
I posted HVAC question recently. I met my architect today and I brought up the question about heatng my new addition with radiant heated floor and possibly baseboard radiator. I started looking for radiant heat info online and could not find any complete information about hydraulic system. I read about various parts (PEX tubing, manifold, zone valves, etc.) However I still do not understand...
Started 2 days, 14 hours ago (2009-12-22 03:01:00)
by MGSCP
many of you have asked about this in the past....and I found this on the mondello olds site and copied it here.... 1420-5 Hydraulic Throw-Out Bearing Assembly This kit eliminates the bellhousing to frame clutch cross shaft allowing you all the room you need to install headers. The bearing travels on a special adjustable sleeve screw which allows over .650" travel for any pressure ...
Started 2 days, 17 hours ago (2009-12-21 23:49:00)
by eme3
Horizontal Drilling and hydraulic fracturing are expected to open up the natural gas reserves in this country. I am trying to find out who some of the leading manufacturers of drilling and fracturing equipment and services are who are likely to benefit from the increased exploration, particularly in the marcellus shale region. Any advice?
Started 2 days, 18 hours ago (2009-12-21 22:29:00)
by bmb779
Anybody have an idea how to remove 2 hydraulic tappets stuck in a 1.9tdi pd engine,timing belt broke and wrecked the valves but unable to remove 2 of the tappets as they are sitting below the level of the head casting.
Started 2 days, 22 hours ago (2009-12-21 18:30:00)
by gclark
My question: what indicates a bad hydraulic lifter? I adjusted the valves on my SBC(retrofit hydraulic roller cam and lifters) this weekend using the EOIC method. At each valve, I would back off the adjusting nut, then find zero lash. Then go an additional 1 turn past zero. Most of the valves would require about the same amount of torque to reach 1 turn, but on a couple of them I could ...
Started 3 days ago (2009-12-21 16:48:00)
by Xstreamer
Selling office chair hydraulic base. Working condition. Good for mounting sports seats, etc. Selling at $20. Self collect at YCK area SMS 8.1.2.6.4.7.2.3 [/img]
Started 5 days, 5 hours ago (2009-12-19 11:15:00)
by kushum
Foremen (Civil/Mechanical/Hydraulic) (5 - 7 yrs) AL-Siraaj International Location:Libya Key Skills:Exposure to plan and review engineering activities, Interfacing with other engineering groups and collaborators and interface with the organization. Specialization:Workman/Foreman/TechnicianJob Function:Production/Manufacturing/Maintenance/Pack agingIndustry:Consulting ...
Started 1 week ago (2009-12-17 16:18:00)
by captain_chaos
Hydraulic e-brake system which does your clutch too. Hello everyone Just been thinking about and have to do a project for uni. So I thought of way you can make a hydraulic e-brake press your clutch at the same time. Now, is this a good idea? Would it be effective or not? Is there any need for this sorta system? Because I looked about and not found a single hydraulic e-...
Started 6 days, 16 hours ago (2009-12-18 00:32:00)
by chefwong
AC Hydraulic Jack - 2 Ton with Padded Saddle - NYC Metro Area I have a AC Hydraulic 2 Ton Jack forsale - DK20. Used about 6-7 times max. If you're reading this thread, you know probably know how good the AC stuff is. $350 and I will deliver within reasonable distance of 20 mile ...
Started 1 week, 1 day ago (2009-12-16 11:17:00)
by RSS-Bot
Honda Civic JDM B16A Hydraulic 5spd Manual Trans B16 Honda Civic JDM B16A Hydraulic 5spd Manual Trans B16 US $799.99 (0 Bid) End Date: Wednesday Dec-16-2009 9:05:53 PST Bid now | Add to watch list
Started 1 week, 1 day ago (2009-12-16 15:50:00)
by Pat
Since my shop is not heated, I am thinking about replacing the regular hydraulic fluid in my Ironworker with a synthetic. I do not know if it will achieve the results I am looking for, and I am still considering some sort of reservoir heater. As far as I know synthetic oil formulated for motor vehicles is supposed to keep the same, or nearly same viscosity within all temperature ranges. If the ...
Started 6 days, 3 hours ago (2009-12-18 13:55:00)
by CalgaryBikeBum
Gone pull my cams again this winter to check things out and while i've got it apart was going to replace my hydraulic lifters. Any recommendations on what to put in there? I seem to remember some discussion on it awhile ago but not sure which ones are best. SE211 cams with adjustable pushrods. Nothing to exotic. What do you folks think?
Started 1 week ago (2009-12-17 04:09:00)
by Bee Jay
Bee Jay's LT4 Hot Cam Hydraulic Roller Conversion I've been planning on doing this for a while, replacing my Summit 1105 cam with an LT4 Hot Cam. I finally got all of the pieces. First I found an excellent but used GMPP Hot Cam for only $100. Then I found a set of Comp cam conversion hydraulic lifters (COMP Cams 853-16) for only $200. I then ordered a Retro ...
Started 4 days, 1 hour ago (2009-12-20 16:05:00)
by cshuman
LS Hydraulic Roller Lifters I bought these as a replacement for my L98. They look identical to the stock lifters except the front and rear area above the roller is not slanted up like the stock ones. I could see were maybe with an aggressive cam the lobe may encounter the body of the lifter as it is moving across the roller. Has anyone had any problem with ...
Started 2 days, 23 hours ago (2009-12-21 17:11:00)
by Beecher
I have hated the soggy clutch linkage in my 2003 turbo since the day I first bought it. The clutch never engaged in the same place twice. It would cause me to bog the car at launch or engage on the floor and stall out. Evolution Motorsports has a kit to replace the accumulator and other assisted parts with GT2 parts. It's a simple hydraulic linkage with a master and slave cylinder. The ...
