Topic profile page for Hinge.
This page has aggregated data from forum posts, threads, listings, online discussions, newsgroups, messageboards, and other online sources which contain user generated content for the term: Hinge.
Topic "Hinge" was discussed 36,321 times on 3,558 sites in last 3 months
Started 1 day, 5 hours ago (2009-12-01 00:00:00)
by bronco4fun1977
liftgate with glass no handle but has hinge. probably would not want to ship because of glass. best to call 678 776 3839. please no calls after 10pm eastern. thanks dan 678 776 3839
Started 1 day, 14 hours ago (2009-11-30 15:17:00)
by Whitetail Man
This is going to sound really noobish, but I don't know how to use a hinge style release. Tedlebo sent me a babyhorn out of his generosity, and I realized today when it came in the mail and I went to try it out that I don't know how to get my bow drawn back with one. Instructions on how to operate a hinge style release needed. Thanks.
Started 1 day, 14 hours ago (2009-11-30 15:14:00)
by Mars47
I'm building a pump and like the title says, I'm in the market for a single trigger hinge frame. I would like it to be gloss black, and I would like it to be Dye, but if the offer comes up for a chrome one for a good price, I'll take it too. I will also look at other brand frames. I'm currently in Iraq, and I'm hunting down parts for this for when I get back to the states; so I can wait for...
Started 6 days, 17 hours ago (2009-11-25 11:57:00)
by adirondackP71
I just finished replacing the lower hinge pin/bushings in drivers door using this kit(part # from BOK). It does work but one mod has to be done: The holes where bushings go in as an interference fit must be drilled out to 31/64. (The new bushings have a larger OD than originals). Then I put a couple drops of Gorilla Glue around outside of bushings to help keep them from spinning in ears of ...
Started 6 days, 14 hours ago (2009-11-25 15:02:00)
by Mattingly93
Ok so i thought i knew what i was doing...but pretty sure i was wrong, any way that the suicide door hinge pockets will still work right if there are offset from each other....this is on a 93 single cab ranger and they are offset because the seat belt bracket was in the way, the bottom hinge sits about half inch to the outside of the truck more than the top hinge.
Started 5 days, 3 hours ago (2009-11-27 02:20:00)
by fmrbydaytkrbynight
I have a peterbilt 379 had the door hinge wore out so I replaced it with a new one. Now for the life of me I can't get this door adjusted. If I get it slid far enough forward for it to shut it leaves a huge gap at the top of the door. If I slide it over to close the gap at the top, the door won't shut. I know it sounds simple but for some reason I'm not seeing the solution. Anyone have any ...
Started 6 days, 9 hours ago (2009-11-25 20:47:00)
by benjiboy8000
Hey everyone i need to buy a new boot hinge its the part thats the same colour as the car that sits on the back bumper. I have the chrome boot clips on the back and someone has tried to get these off and has broken the clip!! does anyone know roughly how much these cost? and if it just fits back in place? If your not sure about the part i mean give me your email address and i will email a ...
Started 1 week ago (2009-11-24 16:58:00)
by d88co88
Hi, I was have a powerbook g4 titanium and the right hinge broke. Also with it, a black cable ripped. Every time I open it now it sparks from that wire. Is it the backlight power cable? If so, what do I need to replace and where can I get it? 800 MHz PowerBook G4 Titanium 1GB ram...
Started 1 week ago (2009-11-25 05:09:00)
by carbuff
Hi, Im changing the pins and bushings in my 92 lx verts door hinges and Im wondering if the little wheel thing that keeps the door open can be fixed also. The wheel seems fine but the metal spring thing doesnt seem to touch it. Its like this on both sides. Is it possible to fix this as its really annoying.
Started 3 days, 19 hours ago (2009-11-28 10:17:00)
by deano external usenet poster
I've taken out a chimney breast, ground floor only, had steels made and installed to support the existing load and have rebuilt a false chimney breast (out of studwork) around the steels to house a 50" plasma, a base unit for A/V components and a long alcove shelf above (to house DVDs). I want to cover the DVD alcove with a long single pane of smoked glass (approx 1240mm wide by 250mm ...
![Trucks [ Eighteen Wheelers ]](http://icons.boardreader.com/3b/11/3b113e0c556c289ab3adf854ec79d60f.png "Trucks [ Eighteen Wheelers ]"){kind=icon}
