Topic profile page for Body panel.
This page has aggregated data from forum posts, threads, listings, online discussions, newsgroups, messageboards, and other online sources which contain user generated content for the term: Body panel.
Topic "Body panel" was discussed 0 times on 0 sites in last 3 months
Started 5 days, 9 hours ago (2009-12-22 20:18:00)
by jmattley
Anyone know where I can get a rear main body panel from? I'm guessing an official LR part but where can I actually order one from? It's quite important since I bashed it offroad today when a fence tried to eat it!! Bastard ice grr.... Cheers!!
Started 5 days, 14 hours ago (2009-12-22 15:16:00)
by Todd W
All my body panel connection points with each other have popped out they use that cheap christmas tree plastic crap that is pretty much toast after it pops. Other than using small bolt/nut/washer setup is there anything else I can look for? My concern with this is the panels may rip if they get caught on a limb.
Started 1 week, 3 days ago (2009-12-17 15:50:00)
by CBartee87SS
All here is a odd question. I have stripped the interior of my Monte and getting ready to de-rust it all and por-15 the inside of the car. I did notice that in the rear window quarters there are some open pockets in between the interior panels and exterior skin. Has anyone thought of filling these areas with expandable foam insulation? This is to help insulate and reduce sound. Also while I am...
Started 1 week, 4 days ago (2009-12-16 14:13:00)
by kingsway_smartie
I had an SUV clip my driver side front bumper. It cracked the panel in two places so I'm pretty sure I need a new body panel. I took my 2008 Smart to one of the bigger body shops in West Toronto and got a quote for over $1,100 for the panel and paint job. That seemed ridiculously high. The labour and paint charges alone were over $600. Can anyone recommend a source for the panel and a shop ...
Started 2 weeks, 1 day ago (2009-12-12 17:59:00)
by ruf911
If creaking sounds bothers you, then check this out. I was in my garage last week, and I accidentally tripped while my forward motion was stopped by the front quarter panel of the MY06 C2S. I had noticed that the triangular tip of the front quarter panel just below the A pillar beside the mirror was flexing. Wow! I have never had any car that had any flex in a body panel. Then I proceeded to ...
Started 3 weeks ago (2009-12-06 23:05:00)
by Sebastien
Just a simple question, is a front end of a 4dr the same as a 2dr? I need some plastic body parts and the only same color bumper is on a 4dr? Does anyone know?
Started 3 weeks, 4 days ago (2009-12-02 15:50:00)
by Ace Brown
Recently I got too close to a tree stump, and destroyed my taillight (and the guard that was supposed to protect it, which actually caused most of the damage). I am planning on adding some kind of serious body armor like is often seen on Jeeps. I picture a 1/8 steel plate to cover the rear quarter panel bulge with a couple of 1" tubes surounding the taillight. It would be fairly easy on the ...
Started 3 weeks, 5 days ago (2009-12-01 21:11:00)
by alfaLeGacy
Disregard previous post on this, I used my cousin's account by accident... I currently have the body of my 1974 GTV being restored. I am in need of rocker panels, front and rear fenders, rear fender quarter panels, and rear fender wheel arches. My body guy and I went through International Auto Part's magazine to determine what was needed for the vehicle. Can anyone verify the quality of ...
Started 2 days, 3 hours ago (2009-12-26 02:25:00)
by Susieloc
Hi i was wondering if u had any luck my explorer has on 50,000 miles and was cracked for one month then my window blew out i cant get it fixed for a while
Started 1 week, 1 day ago (2009-12-19 18:32:00)
by Alfajay
Quote: Originally Posted by alfaLeGacy Also, where may I find steel panels to replace the windshield pillar? This whole area is rusted out. Any advise would be greatly appreciated.
Started 6 days, 11 hours ago (2009-12-21 18:35:00)
by Phoenix
Originally Posted By: CBartee87SS All here is a odd question. I did notice that in the rear window quarters there are some open pockets in between the interior panels and exterior skin. Has anyone thought of filling these areas with expandable foam insulation? This is to help insulate and reduce sound. Be careful with that. As was already mentioned, the expandable foam will push out with ...
Started 4 days, 12 hours ago (2009-12-23 17:08:00)
by LumberjackStu
If you're looking for a tail light, go through ebay, I did and save several hundered bucks compared to the dealer. Here's a link where you can get one for $55 Toyota FJ Cruiser 07-08 OEM Tail Light:eBay Motors (item 270505306680 end time Jan-21-10 18:32:53 PST)
Started 17 hours, 25 minutes ago (2009-12-27 12:16:00)
by bigdaddykane93
Quote: Originally Posted by Sir Toad maybe...it just depends on what pictures insurance requires...i cant take a picture of every step.....ya know? yeah i know. but can you take pictures of the important stuff like where the original panels are spot welded together? and just brief me on how you did it?
Started 4 days, 17 hours ago (2009-12-23 11:59:00)
by Kernite
Well in anticipation of rolling it all back in the garage have started looking at the bodywork. Bought a Front panel on ebay - paid too much - but its a hell of a lot better than my original one was from a rust point of view but sadly not as straight so before painting am going to rig up something to try and take the bend out of it. Annoyingly whilst good condition for age, the seller had clearly...
