My account: Login | Sign Up
Loading...

Project Phoenix Buggy: The Beast from the East | Thread profile

Thread profile page for "Project Phoenix Buggy: The Beast from the East" on http://www.mallcrawlin.com. This report page is a snippet summary view from a single thread "Project Phoenix Buggy: The Beast from the East", located on the Message Board at http://www.mallcrawlin.com. This thread profile page shows the thread statistics for: Total Authors, Total Thread Posts, and Thread Activity, which are reported in a table below. Additional thread profile information is also shown in the following ways:

1) Top Contributing Authors
2) Related Threads on "eBay Auctions"
3) Related Threads on Other Sites

Warning: These statistics are generated using 'best efforts' and can experience delays and reporting errors at times. Please note that such statistics do not constitute a thread's popularity and/or exact posting volumes at any given reporting period.

Title: Project Phoenix Buggy: The Beast from the East
Site: MallCrawlin.com Forums - Powered by vBulletin  MallCrawlin.com Forums - Powered by vBulletin - site profile
Forum: Featured Builds  Featured Builds - forum profile
Total authors: 307 authors
Total thread posts: 451 post
Thread activity: no new posts during last week
Domain info for: mallcrawlin.com

Thread posts in Project Phoenix Buggy: The Beast from the East:

1. 
Started 2 years, 3 months ago (2006-05-15 17:19:00)  by zjeepin
how'd that housing spreader work out for ya?
Size: 81 bytes
Customize:  Customize "Project Phoenix Buggy: The Beast from the East :: Featured Builds :: MallCrawlin.com Forums - Powered by vBulletin"
2. 
Started 2 years, 3 months ago (2006-05-16 03:35:00)  by OverkillZJ
Quote: Originally Posted by zjeepin how'd that housing spreader work out for ya? Actually, REALLY WELL! We needed it "now", didn't know where to get one... so ya, it actually worked pretty well for a 45 minute crap-fab job. We may need to reinforce it a little to spread it a couple more thousandth's for the ...
Size: 836 bytes
Customize:  Customize "<b>Reply 1</b>: Project Phoenix Buggy: The Beast from the East :: Featured Builds :: MallCrawlin.com Forums - Powered by vBulletin"
3. 
Started 2 years, 3 months ago (2006-05-16 03:37:00)  by OverkillZJ
Quote: Originally Posted by violatedppl those welds are so pretty Which usually means I didn't lay them and steve was bored
Size: 652 bytes
Customize:  Customize "<b>Reply 2</b>: Project Phoenix Buggy: The Beast from the East :: Featured Builds :: MallCrawlin.com Forums - Powered by vBulletin"
4. 
Started 2 years, 3 months ago (2006-05-16 03:46:00)  by chadjans
What size cell you end up going with? Chad
Size: 95 bytes
Customize:  Customize "<b>Reply 3</b>: Project Phoenix Buggy: The Beast from the East :: Featured Builds :: MallCrawlin.com Forums - Powered by vBulletin"
5. 
Started 2 years, 3 months ago (2006-05-16 03:48:00)  by OverkillZJ
15 gallon, only about 12 of which is usable since the stock pump is shorter than the cell. I'll figure out how to extend it eventually, but I didn't want to waste time right now, I'll just keep it full for now.
Size: 248 bytes
Customize:  Customize "<b>Reply 4</b>: Project Phoenix Buggy: The Beast from the East :: Featured Builds :: MallCrawlin.com Forums - Powered by vBulletin"
6. 
Started 2 years, 3 months ago (2006-05-16 05:59:00)  by chadjans
Could one get away with a 19" height cell? Even with the use of the threaded ring? Chad
Size: 145 bytes
Customize:  Customize "<b>Reply 5</b>: Project Phoenix Buggy: The Beast from the East :: Featured Builds :: MallCrawlin.com Forums - Powered by vBulletin"
7. 
Started 2 years, 3 months ago (2006-05-16 12:54:00)  by OverkillZJ
You'd only be able to pickup about 12" of fuel, unless you figure out a way to extend the scren/pickup...
Size: 147 bytes
Customize:  Customize "<b>Reply 6</b>: Project Phoenix Buggy: The Beast from the East :: Featured Builds :: MallCrawlin.com Forums - Powered by vBulletin"
8. 
Started 2 years, 3 months ago (2006-05-16 16:36:00)  by chadjans
Ooops mistyped. 19"=10" Chad
Size: 91 bytes
Customize:  Customize "<b>Reply 7</b>: Project Phoenix Buggy: The Beast from the East :: Featured Builds :: MallCrawlin.com Forums - Powered by vBulletin"
9. 
Started 2 years, 3 months ago (2006-05-16 17:02:00)  by OverkillZJ
oh ya I can't remember off hand what the stock pump height was, but i think it extended from like 10-12", so if you got that BTF ring on top it'd probably be perfect, and use all the fuel in the tank. I'd measure your stock pump though, I've found a lot of crazy litle differences between the gen 1 and 2 zj's lately
Size: 359 bytes
Customize:  Customize "<b>Reply 8</b>: Project Phoenix Buggy: The Beast from the East :: Featured Builds :: MallCrawlin.com Forums - Powered by vBulletin"
10. 
Started 2 years, 3 months ago (2006-05-16 17:55:00)  by zj-monster
I just got this info from Cyberauto.com, it seems that Corbeau does have a seat bracket for the GC. Thought maybe this info would be helpful if you'd still like to have your seats adjustable. I'm looking into this also for my grand since I have a Corbeau seat sitting in my garage that I've always wanted to use. Corbeau Seat Brackets: 93-95 Grand cherokee: Driver Side - D1042NS, Passenger ...
Size: 839 bytes
Customize:  Customize "<b>Reply 9</b>: Project Phoenix Buggy: The Beast from the East :: Featured Builds :: MallCrawlin.com Forums - Powered by vBulletin"
 

Top contributing authors for Project Phoenix Buggy: The Beast from the East

Name Posts
OverkillZJ 56
BigDaveZJ 15
Yota Tony 11
chadjans 9
Cue-Ball 7
Kraqa 7
JohnBoulderCO 7
Tommy 5
ogdak 5
ATL ZJ 4