Tool Making | Forum profile

Forum profile page for Tool Making on http://www.plastics.com. This report page is the aggregated overview from a single forum: Tool Making, located on the Message Board at http://www.plastics.com. This forum profile page summarizes the general forum statistics such as: Users Activity, Forum Activity, and Top Authors, which are reported in either a table or graph below for a given reporting time period. Additional forum profile information for "Tool Making" on the Message Board at http://www.plastics.com is also shown in the following ways:

1) Latest Active Threads
2) Hot Threads for Last Week

Warning: These statistics are generated using 'best efforts' and can experience delays and reporting errors at times. Please note that such statistics do not constitute a forum's popularity and/or exact posting volumes at any given reporting period.

Site:	www.plastics.com (site profile, domain info plastics.com)
Title:	Tool Making
Url:	http://www.plastics.com/forums/viewforum.php?f=9
Users activity:	16 post per thread
Forum activity:	0 active threads during last week

Posting activity on Tool Making:

	Week	Month	3 Months
Threads:	0	5	12
Post:	0	11	19

Tool Making Posting activity graph:

Posts by: day week month

Top authors during last week:

No active authors during last week.

Latest active threads on Tool Making::

Re: Valve gate diameter

Started 3 weeks ago (2009-11-27 16:55:00) by DwightDixon

Size and height of gate vestage will be higher and you should also increase the wall of part slightly under the gate. You will likely have to increase the mold cycle time slightly.

Thread: Show this thread (3 posts)

Size: 180 bytes
Related Threads: Same Site | All Sites
Customize:

Re: Off shore

Started 5 months, 3 weeks ago (2009-06-25 12:53:00) by oldtool

Sell the tool at cost and buy several presses. Make your profits molding. $24/Hr cannot compete with $1.55/Hr. I AM truely sorry

Thread: Show this thread (13 posts)

Size: 178 bytes
Related Threads: Same Site | All Sites
Customize:

Re: MOLDS TO RENT

Started 9 months, 2 weeks ago (2009-03-05 03:49:00) by brian_shih

I have a Turkish customer who produces pretty good quality housewares and does counter trade with his customer in the US. If you were really interested, send me a e-mail. I will introduce you to him. I remember that from my memory they were selling some second hand tools through their website two years ago. Haven't contacted him for a long time and not quite sure if they still have any to sell/...

Thread: Show this thread (4 posts)

Size: 517 bytes
Related Threads: Same Site | All Sites
Customize:

RE: Hi, Ask and/or answer technical questions. HAving

Started 1 year, 9 months ago (2008-03-10 07:01:00) by greg

Hi, Ask and/or answer technical questions. HAving info about what you (your firm) do in your signature can result in getting sales IF you are helpful in the forums and people see that and choose to contact you. While giving a good answer to a post, you may invite that poster to contact you directly for more assistance. Hence, the most helpful posters CAN get sales leads by helping people ...

Thread: Show this thread (4 posts)

Size: 1,009 bytes
Related Threads: Same Site | All Sites
Customize:

Re: Troublesome undercut?

Started 8 months, 1 week ago (2009-04-11 05:10:00) by DwightDixon

What kind of undercut you can pull depends on the modulus of the material you are dealing with and whether the material has sufficient properties when it is ejected. It also depends on whether the part is still trapped in the cavity when it is ejected. You can not cause the material to truly reduce its volume when it is ejected. The part can be deformed and allowed to change its shape, if it ...

Thread: Show this thread (10 posts)

Size: 711 bytes
Related Threads: Same Site | All Sites
Customize:

Hot threads for last week on Tool Making::

No active threads for last week.