Kahr | Forum profile

Forum profile page for Kahr on http://www.pistolsmith.com. This report page is the aggregated overview from a single forum: Kahr, located on the Message Board at http://www.pistolsmith.com. This forum profile page summarizes the general forum statistics such as: Users Activity, Forum Activity, and Top Authors, which are reported in either a table or graph below for a given reporting time period. Additional forum profile information for "Kahr" on the Message Board at http://www.pistolsmith.com is also shown in the following ways:

1) Latest Active Threads
2) Hot Threads for Last Week

Warning: These statistics are generated using 'best efforts' and can experience delays and reporting errors at times. Please note that such statistics do not constitute a forum's popularity and/or exact posting volumes at any given reporting period.

Site:	www.pistolsmith.com (site profile, domain info pistolsmith.com)
Title:	Kahr
Url:	http://www.pistolsmith.com/viewforum.php?f=42
Users activity:	13 post per thread
Forum activity:	1 active thread during last week

Posting activity on Kahr:

	Week	Month	3 Months
Threads:	1	1	4
Post:	1	1	5

Kahr Posting activity graph:

Posts by: day week month

Top authors during last week:

Name

Posts

Latest active threads on Kahr::

Re: Kahr .45 acp question ??

Started 4 days, 10 hours ago (2009-12-06 12:34:00) by Pender1

At this time all of Kahr's .45's are poly. No word as to any plans on making steel one, but then again they are famous for keeping future plans quiet.

Thread: Show this thread (2 posts)

Size: 151 bytes
Related Threads: Same Site | All Sites
Customize:

RE: Recoil spring replacement

Started 2 years, 4 months ago (2007-08-05 16:11:00) by dfariswheel

I don't know what Kahr recommends,. but in my early stainless K9 owner's manual it calls for replacement at 2000 rounds. Some of the MK and PM guns need new springs around 1500 rounds or even less in some cases. Bottom line. When in doubt, replace the spring. Springs are a LOT cheaper than slides and frames.

Thread: Show this thread (5 posts)

Size: 349 bytes
Related Threads: Same Site | All Sites
Customize:

RE: polishing feed ramp

Started 2 years, 5 months ago (2007-07-08 14:46:00) by dfariswheel

You're loading your Kahr the WRONG WAY. Kahr specifically recommends loading the Kahr by locking the slide back, inserting a loaded magazine, and pressing the slide stop. The test for whether to polish the feed ramp is: How does the gun SHOOT. If your Kahr is reliable after the 200 round break in period, there's no need to polish anything, and doing so risks making problems where...

Thread: Show this thread (10 posts)

Size: 781 bytes
Related Threads: Same Site | All Sites
Customize:

Re: need IWB holster for Kahr CW9 and CT

Started 10 months, 2 weeks ago (2009-01-29 02:18:00) by keoki

CROSSBREED. Site on-line.

Thread: Show this thread (3 posts)

Size: 31 bytes
Related Threads: Same Site | All Sites
Customize:

Hot threads for last week on Kahr::

Re: Kahr .45 acp question ?? - 1 new post

Started 4 days, 10 hours ago (2009-12-06 12:34:00) by Pender1

At this time all of Kahr's .45's are poly. No word as to any plans on making steel one, but then again they are famous for keeping future plans quiet.

Thread: Show this thread (2 posts)

Size: 151 bytes
Related Threads: Same Site | All Sites
Customize: