Intake and Exhaust | Forum profile

Sounds like our review is about the same. I was fine with the EL's and the UEL's did not fit. I am installing the EL's on a 2002 WRX now, so they should work nicely for that turbo set up. I think the EL's would be fine for any stage 2 set up. Should be fine for small/medium sized stage 3 turbos (VF-52, 68HTA and some 20g's).

Quote: Originally Posted by Gmachine Showing off how smart you are again? And I know how to poop in the potty, too!!! WINNER!!!! Again, G , thank you for your continued updates. Actually, I'd been about to ask you what kind of cut-off tool you used - your pictures answered it. BTW, after seeing your garage, I don't dare take a picture of mine.

1.Woodstock- pump modded w/ o-ring. First again 2.ProjectSega- pump mooded w/ o-ring 3.Tsunami- Pump modded w/o-ring 4.Deaks2- pump mooded w/ o-ring 5.4snowandrally- pump modded w/ o-ring 6. Schado- pump modded w/ o-ring 7. g0ndor - pump modded with o-ring 8. brock sampson - pump modded with o-ring 9. cjlgt06 - pump modded with o-ring 10.LosAngelesGT pump modded w/o-ring 11.Brooklyngenius pump modded w/o-ring 12.Fraggle- pump modd w/o-ring...

Quote: Originally Posted by Gmachine Cut off another 1/2 inch. It's better but i may end up cutting off another 1 to 1.5 in. till i'm happy with it. Don't want to take too much off in one cut,so i will stick with 1/2 in cuts. IMO the crossover pipe (that shipped with my kit) is at least 2inchs too long. Something else i noticed,though it may be related to the crossover fiasco. The inlet piping of the mufflers contact my AVO rsb...

Crossover pipe has been trimmed to 22.5 in. Muffler now sits in bumper cutout,but not perfect yet. I may have to trim down to 22 or 21.5in. Installed midpipe,flex does rub on heat shield. Should be easy fix. Tonights observations: 1.Both mufflers rub a little on bumper cover and rear inside bodywork 2.Left side toe link just hits Y pipe with suspension at full droop. May not be a big deal with car on the ground. 3.Left sway bracket (AVO) will...

awesome so this is what I get when trying to contact invidia. (sales@jetworld.com) This is an automatically generated Delivery Status Notification THIS IS A WARNING MESSAGE ONLY. YOU DO NOT NEED TO RESEND YOUR MESSAGE. Delivery to the following recipient has been delayed: sales@jetworld.com Message will be retried for 2 more day(s) Technical details of temporary failure: Google tried to deliver your message, but it was rejected by the...

chopped off the donut flange on the Borla and welded on a 3" flat flange with a tapered pipe section is what it sounds like.

might as well buy it to be on the safe side. If you don't end up using it, you can re-sell it on the forum

Quote: Originally Posted by Gmachine IMO the crossover pipe (that shipped with my kit) is at least 2inchs too long. Something else i noticed,though it may be related to the crossover fiasco. The inlet piping of the mufflers contact my AVO rsb bracket reinforcement. Either the situation will improve once i fix the pipe or i will have to grind off some of the bracket. Not putting this one on Invidia yet. It looks like it would clear the factory...

well i got the exhaust in yesterday and I decides to paint it with high temp silver paint :-p I decided that red pipes really wasnt the look i was going for. Thanks for the advise from everyone who contributed to my decision.