|
|
Forum profile page for DIY on http://bbs.scoobynet.com/.
This report page is the aggregated overview from a single forum: DIY, located on the Message Board at http://bbs.scoobynet.com/.
This forum profile page summarizes the general forum statistics such as: Users Activity, Forum Activity, and Top Authors, which are reported in either a table or graph below for a given reporting time period.
Additional forum profile information for "DIY" on the Message Board at http://bbs.scoobynet.com/ is also shown in the following ways:
1) Latest Active Threads
2) Hot Threads for Last Week
Warning: These statistics are generated using 'best efforts' and can experience delays and reporting errors at times. Please note that such statistics do not constitute a forum's popularity and/or exact posting volumes at any given reporting period.
|
|
|
|
|
Posting activity on DIY:
|
|
Week
|
Month
|
3 Months
|
|
Threads:
|
9
|
47
|
268
|
|
Post:
|
17
|
90
|
672
|
|
|
DIY Posting activity graph:
|
Top authors during last week:
|
Name
|
Posts
|
|
P1Fanatic
|
2
|
|
RoShamBo
|
1
|
|
SideShowBob
|
1
|
|
powerman1
|
1
|
|
Odds on
|
1
|
|
DannyBoy007
|
1
|
|
jbl
|
1
|
|
rsedwards
|
1
|
|
Shark Man
|
1
|
|
john_s
|
1
|
|
|
|
Latest active threads on DIY::
Started 3 days, 23 hours ago (2008-09-01 15:33:00)
by RoShamBo
I would assume i need specialist tools for this - anyone guide me on how to do it properly? Cheers. 
Started 3 days, 15 hours ago (2008-09-01 23:21:00)
by rb5_336
I need to run a coax cable from one side of the room to the other, and the normal cable will look naff under the carpet. I've seen thin coax cable listed in maplins, but recommended for short lengths. Is there a thin cable available for my purpose ? or any alternatives ? cheers sean
Started 3 days, 14 hours ago (2008-09-02 00:19:00)
by powerman1
as above it sounds as if your bulbs are rated higher than the transformer so first of all check the VA which is basically the max output so 20va max bulb 20w if you exceed the output the bulb wont be any brighter but will overload the transformer and thermal cutout will operate if this is ok ..bin the transformers and replace
Started 3 weeks, 1 day ago (2008-08-13 16:27:00)
by messiah
...or should I say where to avoid? So who does everyone recommend for good quality with value for money? MFI, Wilkes, Howdens, Magnet? Looked in B&Q and thought they were garbage...
Started 3 days, 22 hours ago (2008-09-01 16:13:00)
by SideShowBob
I would like to try takingon an ambitious project, and soundproof our party wall in the lounge (for starters). Id also like to mount the TV (46" LCD) onto the original wall before doing the soundproofing plasterboarding, so the telly sitsd almost flush within the new wall. Ive found a decent looking solution Wall Soundproofing Solution 2: Resilient Bars which would allow the new ...
Started 5 days, 14 hours ago (2008-08-31 00:43:00)
by jbl
Wife is muttering about a new c/h boiler for next year, present one works fine but is at least 35 yrs old. I believe that there is some formula or other that is used in order to work out what size of boiler is required ? Could someone please tell me. Thanks JBL
Started 2 weeks, 6 days ago (2008-08-16 07:13:00)
by RoShamBo
Any good tips / suggestions for fitting skirting board? I will need to cut several pieces at right (45 degree) angles and I only have a trusty saw ! Any help appreciated.
Started 2 weeks, 1 day ago (2008-08-21 02:28:00)
by ghplumb
SF19, Insulation, Superfoil, self builder, multi layer foil insulation
Started 3 weeks, 1 day ago (2008-08-14 14:52:00)
by j4ckos mate
Should be painting at weekend anyone got any tips with non drip gloss
Started 2 weeks, 2 days ago (2008-08-20 12:20:00)
by mike2.5subaru
Hi, i'm no spark but I've got a charger or something with this type of connector, but can't remember what, hence my interest I've also got these on my speakers and have found somethong that may help in Maplins. L64BA 2 pin din lead hope this helps, let us know if its or Mike
|
|
Hot threads for last week on DIY::
Started 5 days, 14 hours ago (2008-08-31 00:43:00)
by jbl
Wife is muttering about a new c/h boiler for next year, present one works fine but is at least 35 yrs old. I believe that there is some formula or other that is used in order to work out what size of boiler is required ? Could someone please tell me. Thanks JBL
Started 3 days, 23 hours ago (2008-09-01 15:33:00)
by RoShamBo
I would assume i need specialist tools for this - anyone guide me on how to do it properly? Cheers.
Started 3 days, 14 hours ago (2008-09-02 00:19:00)
by powerman1
as above it sounds as if your bulbs are rated higher than the transformer so first of all check the VA which is basically the max output so 20va max bulb 20w if you exceed the output the bulb wont be any brighter but will overload the transformer and thermal cutout will operate if this is ok ..bin the transformers and replace
Started 3 weeks, 1 day ago (2008-08-13 16:27:00)
by messiah
...or should I say where to avoid? So who does everyone recommend for good quality with value for money? MFI, Wilkes, Howdens, Magnet? Looked in B&Q and thought they were garbage...
Started 3 days, 15 hours ago (2008-09-01 23:21:00)
by rb5_336
I need to run a coax cable from one side of the room to the other, and the normal cable will look naff under the carpet. I've seen thin coax cable listed in maplins, but recommended for short lengths. Is there a thin cable available for my purpose ? or any alternatives ? cheers sean
Started 3 days, 22 hours ago (2008-09-01 16:13:00)
by SideShowBob
I would like to try takingon an ambitious project, and soundproof our party wall in the lounge (for starters). Id also like to mount the TV (46" LCD) onto the original wall before doing the soundproofing plasterboarding, so the telly sitsd almost flush within the new wall. Ive found a decent looking solution Wall Soundproofing Solution 2: Resilient Bars which would allow the new ...
|
|
