Posts Topics Forums Images
Search videos from message boards Videos Search messages from microblogs Microblogs Search messages from imdb.com Imdb Search messages from yuku.com Yuku Search messages from lefora.com (free forums) Lefora
My account: Login | Sign Up
Loading... 

RS-232 & IP Control | Forum profile

Forum profile page for RS-232 & IP Control on http://www.remotecentral.com. This report page is the aggregated overview from a single forum: RS-232 & IP Control, located on the Message Board at http://www.remotecentral.com. This forum profile page summarizes the general forum statistics such as: Users Activity, Forum Activity, and Top Authors, which are reported in either a table or graph below for a given reporting time period. Additional forum profile information for "RS-232 & IP Control" on the Message Board at http://www.remotecentral.com is also shown in the following ways:

1) Latest Active Threads
2) Hot Threads for Last Week

Warning: These statistics are generated using 'best efforts' and can experience delays and reporting errors at times. Please note that such statistics do not constitute a forum's popularity and/or exact posting volumes at any given reporting period.

Site: RC Forums: Index of All Universal Remote Control & Home Theater Forums - RS-232 & IP Control (site profile, domain info remotecentral.com)
Title: RS-232 & IP Control
Url: http://www.remotecentral.com/cgi-bin/mboard/rs2...
Users activity: 12 post per thread
Forum activity: 7 active threads during last week
 

Posting activity on RS-232 & IP Control:

  Week Month 3 Months
Threads: 7 24 54
Post: 7 25 65
 

RS-232 & IP Control Posting activity graph:

Posts by:  day  week  month 

Top authors during last week:

Name
Posts
joe sexton
1
user's latest post:
NAD IR and RS-232 issues
Published (2009-11-26 21:55:00)
NAD is a serial nightmare, that said there is a software program available from them that will spit out your commands, you select your device and it gives you a set of drop downs to select commands from. It is a test program that was written about 2-3 years ago, I am not sure if they have been updating it for their new gear or not?
Prylbogen
1
user's latest post:
Benq W9000 Projector RS232 control
Published (2009-11-28 03:46:00)
Anybody controling Benq W9000 through rs232? I've seen threads on other Benq models. Wiring is probably the same. I asume 3-wire connection will work without shortening any pins on either side. Protocol seems to be different for most models, so far i have found three different specs for Benq projectors but none of them say they are for W9000 model.
kstrange
1
user's latest post:
Benq W9000 Projector RS232 control
Published (2009-11-29 20:55:00)
I've done a W10000. You'll most likely need a DB9 to DIN cable from "Cables to Go". I don't remember the exact model number for the adapter cable but if I can remember tomorrow when I head into work, I'll check.
jbr64
1
user's latest post:
Marantz SR5004 RS232 Code List
Published (2009-12-02 03:52:00)
Thanks, very nice. Do you by any chance have the additional codes for the SR6004...? /jbr
hwong14
1
user's latest post:
How and where do I learn about...
Published (2009-12-03 14:58:00)
Thanks Joe for your help. Henry
stjoh
1
user's latest post:
Need RS 232 help.
Published (2009-12-05 09:27:00)
Checksum is typically calculated based on the command so most likely you'll have to create a new one for each command.
danieljgor
1
user's latest post:
Need RS 232 help.
Published (2009-12-04 05:53:00)
Hi Guy's I have Played with alot od Ascii RS232 devices, but cannot make sense of my Everfocus DVR. For instance REC to DVD with id 5 0x85 (length) 0x00 (receiver id high byte) 0x05 (receiver id low byte) 0x4B (OPcodekey) 0x08 (Data key = rec) 0x5d (checksum) Play Code is 0B so is bellow correct or will check sum change? 0x85 (length) 0x00 (receiver id high byte) 0x05 (receiver id low byte) 0x4B (OPcodekey) 0x0B (Data key = Play) 0x5d...
 

Latest active threads on RS-232 & IP Control::

RC Forums: Index of All Universal Remote Control & Home Theater Forums
Started 7 months, 2 weeks ago (2009-04-21 02:47:00)  by Casentis
I found these commands: RS232 Baud: 9600 Parity: N Data Bits: 8 Stop Bits: 1 0,1,*,PUT,System(Power_Control(Power=On)),*\x0D\x0 A 0,1,*,PUT,System(Power_Control(Power=Standby)),*\x 0D\x0A
Thread:  Show this thread (153 posts)   Thread info: Yamaha RX-V3900 RS232 Commands? Size: 273 bytes
Related Threads: Same Site | All Sites
Customize:  Customize "RE: Yamaha RX-V3900 RS232 Commands? :: RS-232 & IP Control :: RC Forums: Index of All Universal Remote Control &..."
 

Hot threads for last week on RS-232 & IP Control::

RS-232 & IP Control
Started 7 months, 2 weeks ago (2009-04-21 02:47:00)  by Casentis
I found these commands: RS232 Baud: 9600 Parity: N Data Bits: 8 Stop Bits: 1 0,1,*,PUT,System(Power_Control(Power=On)),*\x0D\x0 A 0,1,*,PUT,System(Power_Control(Power=Standby)),*\x 0D\x0A
Thread:  Show this thread (153 posts)   Thread info: Yamaha RX-V3900 RS232 Commands? Size: 273 bytes
Related Threads: Same Site | All Sites
Customize:  Customize "RE: Yamaha RX-V3900 RS232 Commands? :: RS-232 & IP Control :: RC Forums: Index of All Universal Remote Control &..."