Washer Repair | Forum profile

when blowing back to the tube should the air come out in the tube? I am assuming the above is a typo and the last tube should be tub. Yes air should come out inside the tub whwn checking/clearing a plugged tube.

Here are your parts Replacement parts for MAYTAG MAH6500AWW | AppliancePartsPros.com The following should help http://www.servicematters.com/maytag...s/16010061. pdf http://www.servicematters.com/maytag...DL-0051A-B. pdf Also here a couple threads on this Tension Wire Around Boot Drain Kit Whirlpool washer smells moldy whenever idle

The replacement motor coupling has a metal lining to prevent that part from breaking in the future. it is not possible to repair the coupling because there is way too much torque. There is no certain way to line it all back up just make sure the coupling slides in place and put the motor clips back on and all that good stuff and your good to go

Sounds like a timer problem, Part number: AP3084481 but before you replace it lets get some more info. 1. Does this happen in all cycles? 2. If you open the lid for a few seconds and put it back down does it start up? 3. If you manually move the timer to spin, will it start? 4. Does it happen on the drain spin after the wash and after the rinse cycles?...

If you take off the bottom service panel you should find some tech notes which will show you how to put it into test/troubleshooting mode. See if this tells you anything about the problem. Good luck.

Just today I was called out to repair a washer with this same problem ... I pulled the front pannel and found the impeller on the pump not spinning freely ... I replace the pump and now its working again ... I sugest you look to see if this could also be your problem. Back to Results Pump and motor assembly - By GE. Part Number: AP3160348 Made by GE ...

It is more likely the lid switch is bad. By pass it by taking off the two screws that hold the console to the top (they may be in front, back or under trim pieces) and flip up the console. Disconnect the lid switch connector and insert a solid insulated short piece of wire with the ends exposed in to the two outer holes of the connector coming from the console. Try the machine and if it ...

Well I do not get anything under those part numbers. Here is the part that ties to your control board on this site. Since there is some confusion check with whomever you order from to confirm. Part number: AP4358809 As far as doing it yourself, it is a pretty easy job, no special tools, just remove and replace. This service manual will show you how to get into the ...

I am not sure where your problem is, but the bolt should be right under the cap, and you probably need to use a 7/16" socket with extension and not a 5/16".

Here are your parts Replacement parts for MAYTAG MAH6500AWW | AppliancePartsPros.com The following should help http://www.servicematters.com/maytag...s/16010061. pdf http://www.servicematters.com/maytag...DL-0051A-B. pdf Also here a couple threads on this Tension Wire Around Boot Drain Kit Whirlpool washer smells moldy whenever idle

Check the fuse next to the lid switch if you haven’t already done so. Also check the lid switch actuator to make sure it is making the lid switch when you close the lid. If all of that seems ok the timer is most likely but I would hate to guess on such an expensive part. If the above doesn’t work post back and I will try to help you diagnose the timer. As for continuity ...

Here is the parts breakdown Replacement parts for FRG ATFB6000ES1 | AppliancePartsPros.com Here is the tech sheet http://manuals.frigidaire.com/prodin...0ts_wd_efs. pdf Here is a manual http://frigidaireservicetips.com/pdf...sherManual. pdf Try running the diagnostics to see if you can get an error code which will help narrow it down

I unplugged the washer, let it sit for an hour, reset the controls and ran the washer and it WORKED! I did notice a slight burning odor but very slight. I am happy the washer is working but what about that slight burning odor? Any ideas anyone? Thanks so much people!

If you get the right lid switch you will not have to cut the wires. To replace the lid switch you have to remove the case of the washer. This page will help Whirlpool Washer Disassembly Guide

You have a plastic comb filter under the spin basket that is clogged. Dump a gallon of vinegar in the tub and let it sit for a period of time, might just dissolve the soap residue on the comb filter.

When I moved my washer to clean behind it, I found that the floor was covered with oil (about 2.5 foot square). Washer is less than 2 years old and, so far, seems to be working fine (no odd noises...yet). From my research, the only component that could have been leaking oil would be the gearcase. Is this a common problem for Kenmore?? Although it seems to me that Sears should cover such an ...

The lid switch causes this most of the time. You will have to remove the case of the washer to access the lid switch. This page will help! Whirlpool Washer Disassembly Guide

If you take off the bottom service panel you should find some tech notes which will show you how to put it into test/troubleshooting mode. See if this tells you anything about the problem. Good luck.