Gigbyte Motherboards | Forum profile

It is possible to design a PS/2 mouse port such that it can be split, and the splitters that support this are readily available and inexpensive (under $10, sometimes under $5). However, not all PS/2 ports do support this ... the port has to be designed specifically to enable such support. I do not know about your particular hardware, I can only suggest that you get a splitter and try it. Sparky wrote: I'm looking at a new machine with...

Bill wrote: "Edward" wrote in message ... I built a new system using a GV-N98tsl-1g1 graphics card. The drivers have installed and updated, but I cannot install the software on the CD. It starts, loads the splash screen, then locks up. I am using Windows 7, 64 bit. Any suggestions? Gigabyte tech support has not responded to my email in three days. Anyone have a phone number for tech support in the U.S.? I hope you were able...

Am Wed, 11 Nov 2009 11:56:29 -0500 schrieb Barry Watzman: But that means that the identical modules go in DIFFERENT color sockets. Which confuses a lot of people. That's it - and to be honest I didn't know this before you clarified things. Thanks Barry for your time and explanation - highly appreciated! -- cu Michael

"Edward" wrote in message ... Bill wrote: "Edward" wrote in message ... I built a new system using a GV-N98tsl-1g1 graphics card. The drivers have installed and updated, but I cannot install the software on the CD. It starts, loads the splash screen, then locks up. I am using Windows 7, 64 bit. Any suggestions? Gigabyte tech support has not responded to my email in three days. Anyone have a phone number for...

Barry Watzman wrote: Ok, I have a Gigabyte GA-ex58-UDR3 motherboard, but actually I think that this question is pretty generic and would apply to almost any modern motherboard. I have a SATA hard drive, connected to a SATA port of the Intel ICH10R chipset [actually, I have two SATA hard drives, and two SATA optical drives]. The motherboard has a "Gigabyte" IDE/SATA controller on it to provide an IDE port (and additional SATA...

On Fri, 06 Nov 2009 06:44:05 -0600, Edward wrote: I built a new system using a GV-N98tsl-1g1 graphics card. The drivers have installed and updated, but I cannot install the software on the CD. It starts, loads the splash screen, then locks up. I am using Windows 7, 64 bit. Any suggestions? Gigabyte tech support has not responded to my email in three days. Anyone have a phone number for tech support in the U.S.? I have seen that a windows 7...

Are you talking about Password to access the BIOS or passwords for XP. It is my understanding that even with that board having dual BIOS there is only one password. A XP password would have nothing to do with the BIOS.....its an XP problem. peter -- If you find a posting or message from me offensive,inappropriate or disruptive,please ignore it. If you dont know how to ignore a posting complain to me and I will be only too happy to demonstrate...

The author has marked this message not to be archived. This post will be deleted on November 24, 2009. On Mon, 09 Nov 2009 21:57:18 -0500, Barry Watzman wrote: :Ok, I have a Gigabyte GA-ex58-UDR3 motherboard, but actually I think :that this question is pretty generic and would apply to almost any :modern motherboard. : :I have a SATA hard drive, connected to a SATA port of the Intel ICH10R :chipset [actually, I have two SATA hard drives, and...

The author has marked this message not to be archived. This post will be deleted on November 25, 2009. "peter" wrote in : Are you talking about Password to access the BIOS or passwords for XP. It is my understanding that even with that board having dual BIOS there is only one password. A XP password would have nothing to do with the BIOS.....its an XP problem. peter There are two passwords on that board's bios. One is...

That has been asked before and the switch to AHCI has to be made before installing anything. However, people who've made the switch have not reported any significant speed improvement. --g